Cold air induction kit

Moderators: Regional Representative, Technical Advisor

Forum rules
Only fully subscribed club members may post in this section. Please keep these threads on topic.
Post Reply
Rebel

Cold air induction kit

Post by Rebel » Sat Jun 05, 2010 11:24 am

Anyone fitted a cold air induction kit on a TBI? Been looking across he pond for around $20 - $100 but shipping is $45 - $65, then + import + vat

http://cgi.ebay.com/ebaymotors/ws/eBayI ... MEWAX%3AIT

Have looked at non drop aircleaner 3" tall element as to not interfere with the TBI components but would like to route the filter to the front like below but add an extra length.

Any ideas?

Image

Or use existing filter housing and modd it like this. I know its not pretty but it gives 7-10hp & better air flow than the stock.

Image

User avatar
MarkJ
POC Jr. Poster
Posts: 234
Joined: Sat Feb 14, 2009 9:11 pm
Year: 1988
Model: Trans Am
Engine: 305
Name: Mark Jarrett
Location: Sandwich, kent
Location: Sandwich, Kent
Contact:

Re: Cold air induction kit

Post by MarkJ » Sat Jun 05, 2010 9:47 pm

The stock filter housing on the TBI has a load of sensors and vaccuum pipes attached to it so if you removed it entirely you'd need to work out what you needed to do with them.

Saying that, though the stupid flexi-pipe that runs off it to the front of the engine bay is overly restrictive. When you close the hood it practically blocks the intake entirely. Your idea of removing it and replacing just that pipe with the dome filter might make a bit of difference but at $20 I wouldn't expect miracles. I've never tried it on mine so don't know. I just fitted a K&N ring filter in the existing housing.

User avatar
thebandit92
POC Elite Poster
Posts: 726
Joined: Mon Mar 30, 2009 7:36 am
Year: 1980
Model: Trans Am S/E
Engine: 301
Name: Jimmy
Location: Wigan, England
Location: Wigan, England
Contact:

Re: Cold air induction kit

Post by thebandit92 » Sun Jun 06, 2010 8:33 am

You can buy stainless tubing,silicone hose in different colours and universal filters on ebay uk and then you can run it however you like. http://stores.ebay.co.uk/Auto-Performan ... ec0Q2em322
http://bandittransport.co.uk/

ITS THAT STREAK OF BLACK LIGHTNING CALLED THE BANDIT EXPRESS

:2ndgen:

Rebel

Re: Cold air induction kit

Post by Rebel » Sun Jun 06, 2010 11:18 am

Only one sensor that needs to be attached found this:

The small vacume line for the THERMAC valve can be removed because it is not used, then plug the vacume port an the TBI where it was attached. the IAT sensor which plugs into the bottom of the air cleaner fit right into a port which was on the side of the new assembly. and the PCV tube which goes to the air cleaner can be removed and replaced with a valve cover breather. the attached pic shows the plugged THERMAC port, and the IAT sensor. i know this setup doesn't look perfectly at home on a Camaro, but it does one important task. it enables you to remove the air cleaner spacer thus unshrouding the throttle bores, which allows air to flow in around the bottom of the injector pods rather than squeezing around them from the top.

Image

Thanks thebandit92, been looking for parts, a bit of DIY i can see next week.

User avatar
MarkJ
POC Jr. Poster
Posts: 234
Joined: Sat Feb 14, 2009 9:11 pm
Year: 1988
Model: Trans Am
Engine: 305
Name: Mark Jarrett
Location: Sandwich, kent
Location: Sandwich, Kent
Contact:

Re: Cold air induction kit

Post by MarkJ » Sun Jun 06, 2010 2:23 pm

Let us know how you get on, dude. Would be interesting to see whether this simple mod wakes the 305TBI up at all.#

There are a few articles over on Thirdgen.org that give some good pointers on improving the TBI equipped 305.

http://www.thirdgen.org/ultimatetbi

http://www.thirdgen.org/ultimatetbi2

There's also the attached PDF that I found years ago whilst poking around on the web. Might be of some use.
You do not have the required permissions to view the files attached to this post.

SUPERCHARGEDGTA

Re: Cold air induction kit

Post by SUPERCHARGEDGTA » Sun Jun 06, 2010 9:33 pm

if you remove the carbon canister in the front corner of the engine bay, you can cut out the panel under it. if you fit the induction filter here, this will allow you to draw cold air from outside the engine bay (modified davids to do this) ;)

Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests